We have noticed this post about A Step-by-Step Guide to Installing a Bathtub below on the net and decided it made sense to share it with you in this article.
Mounting a tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately challenging project. If the old bathtub is readily obtainable, the job can move immediately; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will require an assistant to move out the old tub and embeded in the brand-new one. Make sure you have certified on your own for the job as well as fit attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a new bath tub in your bathroom if you have actually currently gotten a new tub and also do not need to change the setup of your previous water supply pipelines.
Your tools and material checklist ought to comprise the following:
Getting ready for the Installation
Firstly, the supporting structure supplied with the bath should be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop pressure on the bath tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, place the tub in the required setting. The wooden boards are useful in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small points.
The next goal is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the tub till the spirit level reads degree.
To set up taps, fit the bottom of the furthest flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub as well as additionally check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, fix the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub must wait till the bath tub has actually been used at the very least when as this will resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin making sure that the washing machines are in location between the tap and the sink. Protect the tap in position with the supplier provided backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former type needs to be linked to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a rigid seal, causing the water to penetrate the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can fracture relatively very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is recommended to fit the floor tiles using water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that editorial on How to Install a Bathtub from an acquaintance on another web blog. In case you enjoyed reading our blog posting plz do not forget to pass it around. I thank you for reading our article about Tools You Need to Install a New Bathtub .
Dial instantly!